<form id="vrefx"></form>

    <nobr id="vrefx"></nobr>

    <nav id="vrefx"><listing id="vrefx"></listing></nav>

    • 18764172899
      0531一85977876

    • [field:companyname]
      全國咨詢熱線
    當前位置:首頁 - 新聞資訊 > 常見新聞 >

    斷橋鋁門窗設備出現供電不穩定的影響

    來源:http://www.thinkgreeninitiative.com/ 發布時間:2021-12-16
    (1)設備停機。盡管沒有形成物理損壞,但容易可編程控制器的程序或邏輯失常、數據丟失或軟件損壞。CNC數據(報括操作體系、參數、程序等)不得不從頭建立或更換PLC等。供電不穩定也會造成設備的電腦意外死機、鎖死或非正常觸發設備NC—PLC復位、CNC體系停止響應等問題,致使設備運行不穩定。重新將電腦復位(通常是關機)才能使軟件恢復正常作業。
    (1) Equipment shutdown. Although there is no physical damage, it is easy to cause program or logic disorder, data loss or software damage of PLC. CNC data (including the operating system, parameters, programs, etc.) have to establish or replace the PLC from the beginning. Unstable power supply will also cause the computer of the equipment to crash unexpectedly, lock or abnormally trigger the nc-plc reset of the equipment and the stop response of the CNC system, resulting in the unstable operation of the equipment. Only by resetting the computer (usually shutdown) can the software resume normal operation.
    (2)設備功能下降。如果長時間存在電壓不穩定(電壓波動過大),會造成設備電子元件和電路功能下降,電子元器件使用壽命降低,使門窗設備整體運行壽命縮短,這些也是普遍存在各門窗企業內的問題。
    (2) Equipment function degradation. If there is voltage instability for a long time (excessive voltage fluctuation), it will reduce the function of equipment electronic components and circuits, reduce the service life of electronic components, and shorten the overall operation life of door and window equipment. These are also common problems in door and window enterprises.
    ,斷橋鋁門窗加工設備
    (3)設備元器件損壞。供電不穩或經常斷電可造成各電子元件的損壞,如CPU、I/O接口電路板、驅動電路板、CRT或LCDLED監視器,存儲設備如RAM、硬盤和通訊接口等。嚴重的瞬時過電壓會造成門窗設備的電子元件或電路板燒壞,從而影響設備正常運行。
    (3) Equipment components are damaged. Unstable power supply or frequent power failure can cause damage to various electronic components, such as CPU, I / O interface circuit board, drive circuit board, CRT or lcled monitor, storage devices such as RAM, hard disk and communication interface. Serious instantaneous overvoltage will burn out the electronic components or circuit board of door and window equipment, thus affecting the normal operation of the equipment.
    塑鋼門窗設備從大體上來講有切割、焊接、清潔類設備,另外還有一些銑削設備,這種設備主要用來加工門窗的凹槽和門窗鎖孔的,這是門窗的加工過程所決定的,每一種設備都有自己獨特的用處,因此這些設備在某種程度上來講,都是必要的,同時選擇品質好的門窗加工設備,才能制作更高品質的塑鋼門窗。
    Generally speaking, plastic steel door and window equipment includes cutting, welding and cleaning equipment, as well as some milling equipment. This equipment is mainly used to process the grooves and lock holes of doors and windows, which is determined by the processing process of doors and windows. Each equipment has its own unique use, so these equipment are necessary to some extent, At the same time, only by selecting high-quality door and window processing equipment can we make higher quality plastic steel doors and windows.